Microbial induced wettability alteration with implications for Underground Hydrogen Storage.

Characterization of the microbial activity impacts on transport and storage of hydrogen is a crucial aspect of successful Underground Hydrogen Storage (UHS). Microbes can use hydrogen for their metabolism, which can then lead to formation of biofilms. Biofilms can potentially alter the wettability of the system and, consequently, impact the flow dynamics and trapping mechanisms in the reservoir. In this study, we investigate the impact of microbial activity on wettability of the hydrogen/brine/rock system, using the captive-bubble cell experimental approach. Apparent contact angles are measured for bubbles of pure hydrogen in contact with a solid surface inside a cell filled with living brine which contains sulphate reducing microbes. To investigate the impact of surface roughness, two different solid samples are used: a "rough" Bentheimer Sandstone sample and a "smooth" pure Quartz sample. It is found that, in systems where buoyancy and interfacial forces are the main acting forces, the impact of biofilm formation on the apparent contact angle highly depends on the surface roughness. For the "rough" Bentheimer sandstone, the apparent contact angle was unchanged by biofilm formation, while for the smooth pure Quartz sample the apparent contact angle decreased significantly, making the system more water-wet. This decrease in apparent contact angle is in contrast with an earlier study present in the literature where a significant increase in contact angle due to microbial activity was reported. The wettability of the biofilm is mainly determined by the consistency of the Extracellular Polymeric Substances (EPS) which depends on the growth conditions in the system. Therefore, to determine the impact of microbial activity on the wettability during UHS will require accurate replication of the reservoir conditions including surface roughness, chemical composition of the brine, the microbial community, as well as temperature, pressure and pH-value conditions.

[Effect of different cleaning methods on bond strength and surface wettability of high translucency zirconia].

PURPOSE: To study the effect of different cleaning methods on the shear bond strength of self-adhesive resin cement to saliva-contaminated high translucency zirconia and surface wettability. METHODS: Eighty zirconia specimens were randomly divided into 5 groups (n=16), i.e., control group(not contaminated), 75% ethanol group,cleaning paste group,airborne-particle abrasion group, and atmospheric pressure cold plasma group. The contact angles was measured, shear bond strength were examined, and fracture types were determined. SPSS 26.0 software package was used for statistical analysis of the data. RESULTS: The atmospheric pressure cold plasma group produced the lowest contact angle(P＜0.05). The shear bond strength of the airborne-particle abrasion group, the cleaning paste group and the atmospheric pressure cold plasma group respectively were similar to the control group without significant difference(P＞0.05), while those were significantly higher than 75% ethanol group(P＜0.05). The mixed fracture mode of the atmospheric pressure cold plasma group evidently increased. CONCLUSIONS: Airborne-particle abrasion, cleaning paste and atmospheric pressure cold plasma overcome the effects of saliva contamination, producing the shear bond strength to zirconia similar to the control group. The atmospheric pressure cold plasma improves hydrophilicity of high translucency zirconia significantly.

Influence of carboxymethyl cellulose on the stability, rheology, and curcumin bioaccessibility of high internal phase Pickering emulsions.

Recently, there has been a focus on using biopolymer-based particles to stabilize high internal phase Pickering emulsions (HIPPEs) due to the notable advances in biocompatibility and biodegradability. In this work, the complex particles of peanut protein isolate and carboxymethyl cellulose (CMC) with various substitution degrees (DS; 0.7 and 0.9) and weight average molecular weights (Mw; 90, 250, and 700 kDa) were prepared and characterized as novel stabilizers. For the obtained four types of morphologically distinct particles, the complex particles formed by CMC (0.9 DS and 250 kDa) showed cluster structures with an average size of 1.271 µm, equally biphasic wettability with three-phase contact angles of 91.5°, and the highest diffusion rate at the oil-water interface. HIPPEs stabilized by these particles exhibited more elastic behavior due to the smaller tanδ and higher viscosity, as well as excellent thixotropic recovery properties and stability against heating, storage, and freeze-thawing. Furthermore, confocal laser scanning microscopy verified that these particles formed a dense interfacial layer around the oil droplets, which could resist flocculation and coalescence between oil droplets during in vitro digestion. The improved bioaccessibility of curcumin-loaded HIPPEs made these delivery systems potentially apply in functional foods.

Wettability and Bactericidal Properties of Bioinspired ZnO Nanopillar Surfaces.

Nanomaterials of zinc oxide (ZnO) exhibit antibacterial activities under ambient illumination that result in cell membrane permeability and disorganization, representing an important opportunity for health-related applications. However, the development of antibiofouling surfaces incorporating ZnO nanomaterials has remained limited. In this work, we fabricate superhydrophobic surfaces based on ZnO nanopillars. Water droplets on these superhydrophobic surfaces exhibit small contact angle hysteresis (within 2-3°) and a minimal tilting angle of 1°. Further, falling droplets bounce off when impacting the superhydrophobic ZnO surfaces with a range of Weber numbers (8-46), demonstrating that the surface facilitates a robust Cassie-Baxter wetting state. In addition, the antibiofouling efficacy of the surfaces has been established against model pathogenic Gram-positive bacteria Staphylococcus aureus (S. aureus) and Gram-negative bacteria Escherichia coli (E. coli). No viable colonies of E. coli were recoverable on the superhydrophobic surfaces of ZnO nanopillars incubated with cultured bacterial solutions for 18 h. Further, our tests demonstrate a substantial reduction in the quantity of S. aureus that attached to the superhydrophobic ZnO nanopillars. Thus, the superhydrophobic ZnO surfaces offer a viable design of antibiofouling materials that do not require additional UV illumination or antimicrobial agents.

Understanding the petal effect: Wetting properties and surface structure of natural rose petals and rose petal-derived surfaces.

The petal effect is identified as a non-wetting state with high drop adhesion. The wetting behavior of petal surfaces is attributed to the papillose structure of their epidermis, which leads to a Cassie-Baxter regime combined with strong pinning sites. Under this scenario, sessile drops are pearl shaped and, unlike lotus-like surfaces, firmly attached to the surface. Petal surfaces are used as inspiration for the fabrication of functional parahydrophobic surfaces such as antibacterial or water-harvesting surfaces. In this work, two types of rose petals were replicated by using a templating technique based in Polydimethylsiloxane (PDMS) nanocasting. The topographic structure, the condensation mechanism under saturated environments and the wetting properties of the natural rose petal and their negative and positive replicas were analyzed. Finally, we performed prospective ice adhesion studies to elucidate whether petal-like surfaces may be used as deicing solutions.

Application of hydroxypropyl methylcellulose to improve the wettability of chitosan coating and its preservation performance on tangerine fruits.

Hydroxypropyl methylcellulose (HPMC) was employed as an intermediate layer to enhance interfacial interaction between chitosan (CS) coating and tangerine fruits, thereby improving the preservation effect. Owing to the low surface tension of tangerine fruit (26.04 mN/m), CS coating solutions showed poor wetting properties on fruit peels (contact angle > 100°). However, by applying a 1.0 % (w/v) HPMC coating on fruits, the contact angle of CS solutions with concentrations of 0.5 %, 1.0 %, and 1.5 % (w/v) decreased to 47.0°, 47.4°, and 48.5°, respectively, whereas the spreading coefficient increased to -16.0 mN/m, -17.6 mN/m and -19.8 mN/m, respectively. Subsequently, the effects of the coatings on fruit quality were investigated. The results demonstrated the promising performance of HPMC-CS two-layer coating in inhibiting fruit respiration, reducing decay rate, and maintaining nutrient content. Notably, HPMC-1.5%CS coating not only reduced the decay rate of tangerine fruit by 45 % and 31 %, in comparison to the uncoated group (CK) and pure CS coating respectively, but also maintained a high content of ascorbic acid. Therefore, this study confirmed that the use of amphiphilic polymers for improving the surface properties of fruits can effectively facilitate the wetting of hydrophilic coatings on fruits, and significantly improve the fresh-keeping performance of edible coatings.

Hydrophobic solution functions as a multifaceted mosquito repellent by enhancing chemical transfer, altering object tracking, and forming aversive memory.

Developing a safe and potent repellent of mosquitoes applicable to human skins is an effective measure against the spread of mosquito-borne diseases. Recently, we have identified that hydrophobic solutions such as low viscosity polydimethylsiloxane (L-PDMS) spread on a human skin prevent mosquitoes from staying on and biting it. This is likely due to the ability of L-PDMS in wetting mosquito legs and exerting a capillary force from which the mosquitoes attempt to escape. Here we show three additional functions of L-PDMS that can contribute to repel Aedes albopictus, by combining physicochemical analysis and behavioral assays in both an arm cage and a virtual flight arena. First, L-PDMS, when mixed with topical repellents and applied on a human skin, enhances the effect of topical repellents in reducing mosquito bites by efficiently transferring them to mosquito legs upon contact. Second, L-PDMS applied to mosquito tarsi compromises visual object tracking during flight, exerting an influence outlasting the contact. Finally, L-PDMS applied to mosquito tarsi acts as an aversive reinforcer in associative learning, making mosquitoes avoid the conditioned odor. These results uncover a multifaceted potential of L-PDMS in altering a sequence of mosquito behaviors from biting a human skin, visual object tracking following takeoff, to the response to an odor linked with L-PDMS.

Influence of Ultrasound on the Characteristics of CaP Coatings Generated Via the Micro-arc Oxidation Process in Relation to Biomedical Engineering.

Over the past decade, bone tissue engineering has been at the core of attention because of an increasing number of implant surgeries. The purpose of this study was to obtain coatings on titanium (Ti) implants with improved properties in terms of biomedical applications and to investigate the effect of ultrasound (US) on these properties during the micro-arc oxidation (MAO) process. The influence of various process parameters, such as time and current density, as well as US mode, on the properties of such coatings was evaluated. Novel porous calcium-phosphate-based coatings were obtained on commercially pure Ti. Their microstructure, chemical composition, topography, wettability, nanomechanical properties, thickness, adhesion to the substrate, and corrosion resistance were analyzed. In addition, cytocompatibility evaluation was checked with the human osteoblasts. The properties of the coatings varied significantly, depending on applied process parameters. The US application during the MAO process contributes to the increase of coating thickness, porosity, roughness, and skewness, as well as augmented calcium incorporation. The most advantageous coating was obtained at a current of 136 mA, time 450 s, and unipolar rectangular US, as it exhibits high porosity, adequate wettability, and beneficial skewness, which enabled increased adhesion and proliferation of osteoblasts during in vitro studies. Finally, the conducted research demonstrated the influence of various UMAO process parameters, which allowed for the selection of appropriate Ti implant modification for specific biomedical utilization.

The role of air relative humidity on the wettability of Pseudomonas fluorescens AR11 biofilms.

Biofilms are complex porous materials formed by microorganisms, polysaccharides, proteins, eDNA, inorganic matter, and water. They are ubiquitous in various environmental niches and are known to grow at solid-liquid, solid-air and air-liquid interfaces, often causing problems in several industrial and sanitary fields. Their removal is a challenge in many applications and numerous studies have been conducted to identify promising chemical species as cleaning agents. While these substances target specific components of biofilm structure, the role of water content in biofilm, and how it can influence wettability and detergent absorption have been quite neglected in the literature. Estimating water content in biofilm is a challenging task due to its heterogeneity in morphology and chemical composition. In this study, we controlled water content in Pseudomonas fluorescens AR 11 biofilms grown on submerged glass slides by regulating environmental relative humidity after drying. Interfacial properties of biofilm were investigated by measuring wetting of water and soybean oil. The morphology of biofilm structure was evaluated using Confocal Laser Scanning Microscopy and Scanning Electron Microscopy. The results showed that biofilm water content has a significant and measurable effect on its wettability, leading to the hypothesis that a preliminary control of water content can play a crucial role in biofilm removal process.

Enhanced homogeneity and flexibility in a humidity sensor using cellulose nanocrystal-based composite film with circular shear flow.

Cellulose nanocrystal (CNC) film is known to be one kind of dynamic color-sensing material, capable of reversible color changes in response to varying humidity levels. However, the brittleness, low hygroscopicity and poor homogeneity of these films have hindered their development. To address this limitation, we present a novel approach where we combine natural deep eutectic solvents (NADES) with sorbitol under the influence of circular shear flow to craft a CNC humidity-sensitive film with enhanced flexibility, hygroscopicity and homogeneity. The inclusion of sorbitol and NADES enhances hygroscopicity and improves the flexibility. Surprisingly, the introduction of circular shear flow was found not only to improve homogeneity, macroscopically and microscopically, but also to further enhance flexibility, toughness, and water absorption capability. The resulting composite films demonstrated highly reversible color changes across the whole visible spectrum depending on the relative humidity, showing their capability to be reliable humidity-sensing materials. Thanks to the improved homogeneity and flexibility, the obtained humidity-sensing composite film can be employed in its entirety without the need for cutting, making it a promising candidate for various applications.

In Vitro Evaluation of Soft Contact Lens Wettability With a Nonmodified Commercial Videokeratoscope.

PURPOSE: To evaluate a new in vitro technique for measuring soft contact lens wettability using a nonmodified commercial videokeratoscope, the Medmont E300. To this end, the capability of different artificial tears containing hyaluronic acid (HA) to improve soft contact lens wettability in vitro was investigated. METHODS: An experimental in vitro study was conducted to assess the wetting properties of three artificial tears containing different concentrations of HA (0.1%, 0.2%, and 0.3%) on soft contact lenses. A saline solution was used as the control. For each solution, 15 hydrogel (Ocufilcon D) contact lenses and 15 silicone-hydrogel (Somofilcon A) contact lenses were evaluated. The in vitro wettability of the lenses was measured using the Medmont E300 with a self-developed technique, which involved measuring the tear film surface quality (TFSQ) mean, TFSQ area, TFSQ central, and TFSQ inferior. RESULTS: Compared with the saline solution, all the concentration of HA (0.1%, 0.2%, and 0.3%) improved the in vitro wettability of both soft contact lenses by decreasing their TFSQ mean and TFSQ area ( P <0.05). Regression models revealed an exponential relationship between contact lens wettability and the concentration of HA for both soft contact lenses ( R >0.5, P <0.05). Furthermore, the hydrogel contact lens presented a wetter surface than the silicone-hydrogel contact lens ( P <0.05). CONCLUSIONS: The measurement of in vitro wettability of soft contact lenses with a nonmodified Medmont E300 seems to be a useful technique to evaluate the wetting properties of contact lens products.

Evaluating the in vitro wettability and coefficient of friction of a novel and contemporary reusable silicone hydrogel contact lens materials using an in vitro blink model.

PURPOSE: To evaluate the in vitro wettability and coefficient of friction of a novel amphiphilic polymeric surfactant (APS), poly(oxyethylene)-co-poly(oxybutylene) (PEO-PBO) releasing silicone hydrogel (SiHy) contact lens material (serafilcon A), compared to other reusable SiHy lens materials. METHODS: The release of fluorescently-labelled nitrobenzoxadiazole (NBD)-PEO-PBO was evaluated from serafilcon A over 7 days in a vial. The wettability and coefficient of friction of serafilcon A and three contemporary SiHy contact lens materials (senofilcon A; samfilcon A; comfilcon A) were evaluated using an in vitro blink model over their recommended wearing period; t = 0, 1, 7, 14 days for all lens types and t = 30 days for samfilcon A and comfilcon A (n = 4). Sessile drop contact angles were determined and in vitro non-invasive keratographic break-up time (NIKBUT) measurements were assessed on a blink model via the OCULUS Keratograph 5 M. The coefficient of friction was measured using a nano tribometer. RESULTS: The relative fluorescence of NBD-PEO-PBO decreased in serafilcon A by approximately 18 % after 7 days. The amount of NBD-PEO-PBO released on day 7 was 50 % less than the amount released on day 1 (6.5±1.0 vs 3.4±0.5 µg/lens). The reduction in PEO-PBO in the lens also coincided with an increase in contact angles for serafilcon A after 7 days (p < 0.05), although there were no changes in NIKBUT or coefficient of friction (p > 0.05). The other contact lens materials had stable contact angles and NIKBUT over their recommended wearing period (p > 0.05), with the exception of samfilcon A, which had an increase in contact angle after 14 days as compared to t = 0 (p < 0.05). Senofilcon A and samfilcon A also showed an increase in coefficient of friction at 14 and 30 days, respectively, compared to their blister pack values (p < 0.05). CONCLUSION: The results indicate that serafilcon A gradually depletes its reserve of PEO-PBO over 1 week, but this decrease did not significantly change the lens performance in vitro during this time frame.

Enhancing Titanium Disk Performance through In-Pack Cold Atmospheric Plasma Treatment.

While titanium dental implants have already been clinically established, ongoing research is continuously being conducted to advance the fields of osseointegration and bacterial resistance, seeking further improvements in these areas. In this study, we introduce an innovative method for treating titanium surfaces within tightly sealed packaging. Specifically, titanium discs, enclosed in surgical-grade packaging, underwent treatment using cold atmospheric plasma (CAP). The surfaces were thoroughly characterized in terms of wettability, crystalline structure, and chemical composition. Hemocompatibility analyses were conducted using blood diluted in sodium citrate (1:9) exposed to titanium discs for 30 min inside a CO2 incubator at 37 °C. Subsequently, various blood parameters were evaluated, including prothrombin time (PT), activated partial thromboplastin time (APTT), and platelet adhesion. Microbiological analyses were also performed using Pseudomonas aeruginosa (ATCC 27853) for 4 h at 37 °C. The treatment with CAP Jet resulted in a reduction in contact angle without causing any changes in the crystalline structure. No statistically significant differences were observed in the blood parameters. The plasma-treated samples exhibited lower PT and APTT values compared to those of the control group. The surfaces treated with CAP Jet showed increased platelet activation, platelet density, and thrombus formation when compared with the untreated samples. Moreover, the treated surfaces demonstrated lower bacterial colony formation compared with other surfaces.

Evaluation and assessment of the wettabilty and water contact angle of modified poly methyl methacrylate denture base materials against PEEK in cast partial denture framework: an in vitro study.

INTRODUCTION: The prevalence of adults with partially dental arches is expected to be more than imagined and patients requiring replacement of missing teeth are slowly increasing in number too. Removable partial dentures are known to provide for substantial replacement for the missing teeth with also added advantages when compared to fixed or implant prosthesis, mainly in elderly patients. Denture base material performance and durability are greatly influenced by wettability and water contact angle. In the case of dentures; adequate moisture distribution is necessary to ensure excellent wettability which has an influence on comfort and oral health. The purpose of conducting this study was to find out whether the advancements made using PEEK (Polyether ether ketone) would prove to be more beneficial than the current upgrades in the current material spectrum. MATERIALS AND METHODS: This study was performed under in vitro conditions. All the fabrication and processing was done only by one operator. The materials used were divided into three groups each comprising 20 samples. Group A was modified polymethylmethacrylate (Bredent Polyan), Group B was polyoxymethylene acetal resin (Biodentaplast) and Group C was PEEK. An Ossila Goniometer was used to measure the contact angle. The three types of liquids used for the testing included distilled water, natural saliva and mouth wetting solution (Wet Mouth Liquid, ICPA India). Human saliva was collected from an individual with no medical conditions and normal salivary secretion. RESULTS: The data was analyzed using One-way ANOVA test and a pairwise comparison using the Post Hoc Tukey's Honest Significant Difference. Table 1 consists of the mean water contact angles of the denture base materials and mean contact angles of various denture base materials. In saliva, mouth wetting solution and distilled water, the highest mean and least mean contact angle was seen in Polyan and Biodentaplast respectively. A signicant difference was seen between PEEK and Polyan and Biodentaplast and Polyan on further comparison. CONCLUSION: From the resources and the materials at our disposal, it could be concluded that Polyan, Biodentaplast and PEEK and could be used as viable options in cast partial denture framework.

Ferrocene-functionalized polydopamine film timely mediates M1-to-M2 macrophage polarization through adaptive wettability.

Dynamical control of macrophage polarization from M1 (pro-inflammatory) to M2 (anti-inflammatory) at implant surfaces is essential for balancing innate immunity and tissue repair. In this aspect, the design of orthopedic implant that can response to inflammation microenvironment with transformation in surface properties has shown promising in timely driving M1-to-M2 macrophage transition. Considering excessive reactive oxygen species (ROS) contribute to macrophage M1 polarization and progression of inflammation, in this study, ferrocene modified polydopamine (PDA-Fc) films were deposited on plasma sprayed Ti coatings to endow the implants with ROS-responsive and -scavenging abilities. Plasma sprayed Ti (PST) coating and PDA modified PST coating (PST/PDA) served as control. The presence of PDA endowed PST/PDA and PST/PDA-Fc with free-radical scavenging abilities. Moreover, PST/PDA-Fc showed adaptive wettability as evidenced by increased hydrophilicity under H2O2 treatment. With respect to PST/PDA, PST/PDA-Fc exerted greater effects on inducing lipopolysaccharides-induced M1 macrophages to adopt M2-type macrophage phenotype, characterized by higher percentage of CD206-positive cells, increased cell elongation rate and higher expression level of anti-inflammatory cytokine arginase type 1. The results obtained in our study may provide a prospective approach for manipulating an appropriate immune response at implant surfaces.

Bio-copper nanoparticle-based superhydrophobic membranes for sustainable oil/water separation.

The effective separation of oil and water presents a significant global challenge due to the growing prevalence of industrial oily wastewater. In this investigation, a superhydrophobic (SP) coating based on bio-copper (Cu) was successfully created using the grape seed extract and applied onto a textile fabric (TF) to create a highly efficient membrane for oil-water (O-W) separation. The characteristics of the resulting bio-Cu nanoparticles, including surface area, morphology, and composition, were examined. The developed SP TF (STF) membrane, based on bio-Cu, underwent extensive analysis of its wettability, morphology, surface composition, oil absorption capacity, O-W separation performance, flux rate, mechanical stability, and chemical stability. The STF membrane exhibited excellent SP properties, with a high-water contact angle of 156° and a low water sliding angle of 2°, indicating its exceptional ability to repel water. Furthermore, the membrane demonstrated a remarkable oil absorption capacity, separation efficiency, and the flux rate toward three different oils (diesel, corn oil, and kerosene). It displayed good mechanical and chemical stability, with the ability to withstand abrasion and immersion in solutions of different pH values for varying exposure times. These findings highlight the potential of the bio-Cu-based STF membrane as an effective and durable solution for O-W separation applications.

Brochosome size variation and its influence on leafhopper (Hemiptera: Cicadellidae) wing wettability.

Insect wing surfaces have nano- and microscale features that enable multi-functionality. Leafhoppers (Hemiptera: Cicadellidae) are unique in that they produce and excrete nanoscale particles, called brochocosomes, that are spread onto the integument by the insect. Brochosomes are extra-cuticular, removable, and make the integument both superhydrophobic and anti-reflective, 2 greatly desired properties in engineering and material science fields. Adaptations like this have captured the interest of researchers looking to draw inspiration from the natural world to create novel solutions and optimize current technologies. Here, we compare brochosome size and wettability across 8 species of leafhoppers using scanning electron microscopy and microgoniometry. We demonstrate that brochosome size is variable within species and that size and wettability are both significantly impacted by species. We report the extent of variability in each case and examine the relationship between brochosome size, body length, and hydrophobicity. In discussing potential applications for brochosomes, we comment on an emerging and rapid analysis technique for evaluating small biological particles. Additionally, we discuss a few recent brochosome-inspired designs and comment on important considerations. Our work provides valuable insight on a unique system that can guide the design of functionalized materials with enhanced hydrophobic and self-cleaning properties.

Customizing Wettability of Defect-Rich CeO2/TiO2 Nanotube Arrays for Humidity-Resistant, Ultrafast, and Sensitive Ammonia Response.

In all their applications, gas sensors should satisfy several requirements, including low cost, reduced energy consumption, fast response/recovery, high sensitivity, and reliability in a broad humidity range. Unfortunately, the fast response/recovery and sensing reliability under high humidity conditions are often still missing, especially those working at room temperature. In this study, a humidity-resistant gas sensor with an ultrafast response/recovery rate was designed by integrating a defect-rich semiconducting sensing interface and a self-assembled monolayer (SAM) with controllable wettability. As a proof-of-concept application, ammonia (NH3), one of the atmospheric and indoor pollutants, was selected as the target gas. The decoration of interconnected defective CeO2 nanowires on spaced TiO2 nanotube arrays (NTAs) provided superior NH3 sensing performances. Moreover, we showed that manipulating the functional end group of SAMs is an efficient and simple method to adjust the wettability, by which 86% sensitivity retention with an ultrafast response (within 5 s) and a low limit of detection (45 ppb) were achieved even at 75% relative humidity and room temperature. This work provides a new route toward the comprehensive design and application of metal oxide semiconductors for trace gas monitoring under harsh conditions, such as those of agricultural, environmental, and industrial fields.

Comparative analysis of the physical, chemical, and microbiological properties of Ti-6Al-4V disks produced by different methods and subjected to surface treatments.

STATEMENT OF PROBLEM: To improve the osseointegration of dental implants and reduce microbiological growth, different micro- and nanoscale surface topographies can be used. PURPOSE: The purpose of this in vitro study was to evaluate the influence of Ti-6Al-4V with 4 surfaces, machined (DU), machined+hydroxyapatite (DUHAp), machined+acid-alkali treatment (DUAA), and additive manufacturing (DMA), on the physical, chemical, and microbiological properties. MATERIAL AND METHODS: The topography of Ti-6Al-4V disks with the 4 surfaces was evaluated by scanning electron microscopy (SEM), the chemical composition by energy dispersive X-ray spectroscopy (EDS), and the crystalline structure by X-ray diffraction (XRD). Physical and chemical properties were analyzed by using wettability and surface free energy, roughness, and microbial adhesion against Staphylococcus aureus by colony forming units (CFU). One-way ANOVA analysis of variance and the Tukey multiple comparisons test were applied to evaluate the data, except CFU, which was submitted to the Kruskal-Wallis nonparametric test (α=.05). RESULTS: DU photomicrographs showed a topography characteristic of a polished machined surface, DUHAp and DUAA exhibited patterns corresponding to the surface modifications performed, and in DMA the presence of partially fused spherical particles was observed. The EDS identified chemical elements inherent in the Ti-6Al-4V, and the DUHAp and DUAA disks also had the ions from the treatments applied. XRD patterns revealed similarities between DU and DMA, as well as characteristic peaks of hydroxyapatite (HA) in the DUHAp disk and the DUAA. Compared with DU and DMA the DUHAp and DUAA groups showed hydrophilic behavior with smaller contact angles and higher surface free energy (P<.05). DMA showed a higher mean value of roughness, different from the others (P<.05), and a higher CFU for S. aureus (P=.006). CONCLUSIONS: DUHAp and DUAA showed similar behaviors regarding wettability, surface free energy, and bacterial adhesion. Among the untreated groups, DMA exhibited higher roughness, bacterial adhesion, and lower wettability and surface free energy.

Biofunctionalization of surfaces to minimize undesirable effects in cardiovascular assistance devices

BACKGROUND: The reactivity of blood with non-endothelial surface is a challenge for long-term Ventricular Assist Devices development, usually made with pure titanium, which despite of being inert, low density and high mechanical resistance it does not avoid the thrombogenic responses. Here we tested a modification on the titanium surface with Laser Induced Periodic Surface Structures followed by Diamond Like Carbon (DLC) coating in different thicknesses to customize the wettability profile by changing the surface energy of the titanium. METHODS: Four different surfaces were proposed: (1) Pure Titanium as Reference Material (RM), (2) Textured as Test Sample (TS), (3) Textured with DLC 0.3µm as (TSA) and (4) Textured with 2.4µm DLC as (TSB). A single implant was positioned in the abdominal aorta of Wistar rats and the effects of hemodynamic interaction were evaluated without anticoagulant drugs. RESULTS: After twelve weeks, the implants were extracted and subjected to qualitative analysis by Scanning Electron Microscopy under low vacuum and X-ray Energy Dispersion. The regions that remained in contact with the wall of the aorta showed encapsulation of the endothelial tissue. TSB implants, although superhydrophilic, have proven that the DLC coating inhibits the adhesion of biological material, prevents abrasive wear and delamination, as observed in the TS and TSA implants. Pseudo- neointimal layers were heterogeneously identified in higher concentration on Test Surfaces.